Відео

LG 8kg Top load washing grinding and banging when washing

Superb Diagnostic test, worked like a charm, put a voltmeter between the 1st and 4th points shown above and it read 1.2 VAC, so it was bad, I replaced it and it started right back up. Many thanks and God Bless

I am having what I think is this problem, do I have to close the house water?

I already did this and it works great. I bought just the clip on Amazon. To defrost, I put my Samsung in display mode and put A small space heater inside. This has a thermostat, the max temp is about 110F. Reiterating: defrost before you pull off the rear cover.

I already did this and it works great. I bought just the clip on Amazon. To defrost, I put my Samsung in display mode and put A small space heater inside. This has a thermostat, the max temp is about 110F. Reiterating: defrost before you pull off the rear cover.

Thanks for this video. It helped me diagnose why the grill was not heating up.

So after installing the kit one month later all frozen up again. I then (finally) decided to double check the level of the frig and it was leaning forward. Cranked it up and steamed everything and waited and another month and not as bad, but still freezing up. Stumbled across that Samsung had a class action suit so I called them and within 3 days a person arrived and replaced the circuit board and the ice maker and left. No charge! It is now working great. So if you have a Samsung French Door freezing up call Samsung. They will ask for the model and serial # and a picture of the inside of the frozen ice box.

Good video. Just what I was looking for!

Saved me a lot of money and a ton of mental anguish. It looked daunting but I just took it step by step through his video and the process was easy. The hardest part was making sure the voltmeter I had was set right. Never used one before. I had a cheap one from Harber Freight that seemed to do the trick. Note that in the video he said there should NOT be continuity between the blue/Yellow wire on the heating element. When I tested, I found that mine did, so I read the other comments and someone else had the same issue/question. Not to repeat them, find those comments and read them. Reassembly was even easier. Working now like nothing was ever wrong. Big thanks again.

Goes to fast, and what did he use to keep one end in place

Thanks! Can I buy you a coffee

Spot on diagnosis of the cause of my leak. For what it's worth, I tried a work around of blocking flow to the detergent dispenser by capping the outlet for that valve - thinking we don't use that dispenser anyway. The washer then identified a low flow fault when trying to fill the tub - so it did not work. Video was very helpful. Thank you.

what about gas version? thermal fuse?

Help with diagnosis please? Older Whirlpool washer has very little cold water coming in. As initial diagnostic steps I disconnected the hoses, ran them down the drain, and verified water is coming out. Good. So next I swapped the hoses so hot water was connected to cold input and cold water was connected to hot input. Tried again and there’s still almost no cold water. Thoughts?

We’ve been popping out the plug but we’re at the point where some of our residents don’t want the dishwasher anymore, is there anyway to plug back up the hole where it wouldn’t leak?

After over 13 years of trouble free perfect service, my Samsung Ice maker finally stopped working. I've been troubleshooting it now for about 2 days. I have been searching videos and contacted Samsung's Chat which seems useless. I just wanted to take the icemaker out to check it all out but until now, was unsure how. You sir have the best video out there. Thank you.

Dude literally skips the most important step. The screws to open the lid.

Perfect video. I am no handy man by any means. You made it look easy, included every step, and were super thorough. Dryer is running like a champ now.

i have 120volts coming in, no green light, I do not get 5v at the connector. The display lights up but there is a buzzing noise back around the circuit board. Machine does not operate

Thanks so much

Great video but the link is wrong. Amazon sent a part with the wrong number of connectors. Installed it anyway and of course got 02 error codes.

Yes!! This saved me a ton of money in repair costs, and I did it myself in 5 minutes. Thank you!!

My Ice maker wont stop making ice

The troubleshooting on this video helped me out a bunch. Couldn't figure out why my machine tub was banging side to side and it definitely bounces up and down so here's hoping that's the problem!

Nice!

Mine the load and go won’t work

Thank you sir

Did you get a whole new agitator piece? Or just the rusty piece? Ty

SONI did this but the water shut off when I unplugged it but it’s stuck on the wash cycle

It helps if you can shape your ear into a tube and use that like a stethescope to get in and listen to parts individually, but this is very dangerous because your ear can get yanked off and even mangled in the machinery.

Great video for replacing the icemaker. However, the part number link is not correct as Amazon sent the wrong part. After realizing I had the wrong part, called the phone number in the links and they confirmed it was not the correct part, then cost me an additional $45 and had to wait 5 more days to get it from the company the phone number goes to, plus don't like having to give my credit card info to a stranger on the phone.

Need your help I change both front rollers the belt put everything back together, but the drums does not turn. Could it be the felt on the front of the drum I am stuck please help any information is helpful

What would cause a light to be on in a GE built in but still no heat? Fuse & door switch? Just the door switch?

Thank you sir! This did the trick on my Maytag Bravos XL!

Thanks for the video. I performed the diagnostics to make sure the control panel was faulty and followed your instructions step by step. Good stuff.

I replaced mine but the bolt keeps backing out. The bolt you put back in looks new with loctite is that the key to keeping this bolt from backing out?

Awesome video I greatly appreciate it. The squeal is gone but now I have a thumping sound. I can't seem to place. I tested all bearings before closing and the drum before closing and everything seemed good.

Is there a trick to getting the nut off? I’m having a similar issue but it seems to just keep spinning when I’m using the ratchet. I’m even holding the basin, but it keeps spinning.

...and THREE YEARS LATER YOUR VIDEO IS STILL HELPING PEOPLE!!!! Thank you so much for being so generous with your knowledge and time! This video solved my issue along with another video that solved my sensor issue. This video was so helpful and saved me a ton of money! Thanks again and may God richly bless you!

Can you tell me where to get the glass cooktop?? How much it will cost??

My keeps rising like 4 times why lol plz tell me thanks nice video😊

great video, straight to the point and fixed my problem,thank you

Thank you for this video this was my problem and cleaning out the pressure switch fixed it. Thanks so much!

Mine has a click now after the bearing replacement when the tub rotates

Did not fix my POS refrigerator

Any tips on how to make it actually wash the clothes ?? Mines just says socking then drains an is done it don’t really wash them 😑🤦🏻‍♀️😭

I have the same problem but my knob do not have no cracks

Mine keeps repeating the rinse cycle. What can it be. Its not off balance and the suspension rods are new?

I was installing my door and the hinges snapped back and shattered the door glass. Got a new glass and about to try this again.